| ISO |
ISO/TC 29/SC 8 |
Tools for moulding — Guide pillars, straight and shouldered, and locating guide pillars, shouldered |
ISO 8017:2007 |
8017 |
2 |
2007 |
SDG 8
|
| IEC |
TC 105 |
Fuel cell technologies - Part 3-300: Stationary fuel cell power systems - Installation |
IEC 62282-3-300:2012 |
62282-3-300:2012 |
1 |
2012 |
SDG 7, 9, 11, 13
|
| ISO |
ISO/TC 22/SC 38 |
Motorcycles — Methods for setting running resistance on a chassis dynamometer |
ISO 11486:2006 |
11486 |
2 |
2006 |
SDG 9
|
| ISO |
ISO/TC 229 |
Nanotechnologies — Guidance on physico-chemical characterization of engineered nanoscale materials for toxicologic assessment |
ISO/TR 13014:2012 |
13014 |
1 |
2012 |
SDG 3
|
| IEC |
TC 48/SC 48B |
Connectors for electronic equipment - Tests and measurements - Part 7-1: Impact tests (free connectors) - Test 7a: Free fall (repeated) |
IEC 60512-7-1:2010 |
60512-7-1:2010 |
1 |
2010 |
SDG 3, 4, 6, 7, 9, 11, 12, 13, 16, 17
|
| ISO |
ISO/TC 118/SC 4 |
Filters for compressed air — Test methods — Part 2: Oil vapours |
ISO 12500-2:2007 |
12500 |
1 |
2007 |
SDG 9
|
| IEC |
TC 113 |
Nanomanufacturing - Key control characteristics - Part 4-4: Nano-enabled electrical energy storage - Thermal characterization of nanomaterials, nail penetration method |
IEC TS 62607-4-4:2016 |
62607-4-4:2016 |
1 |
2016 |
SDG 9
|
| ISO |
ISO/TC 127/SC 1 |
Earth-moving machinery — Machine-mounted retrieval device — Performance requirements — Technical Corrigendum 1 |
ISO 10532:1995/Cor 1:2006 |
10532 |
1 |
2006 |
SDG 8
|
| IEC |
TC 62/SC 62B |
Medical electrical equipment - Characteristics of digital X-ray imaging devices - Part 1-3: Determination of the detective quantum efficiency - Detectors used in dynamic imaging |
IEC 62220-1-3:2008 |
62220-1-3:2008 |
1 |
2008 |
SDG 3
|
| ISO |
ISO/TC 45/SC 3 |
Rubber test mixes — Preparation, mixing and vulcanization — Equipment and procedures |
ISO 2393:2014 |
2393 |
4 |
2014 |
SDG 9
|
| ISO |
ISO/TC 107/SC 9 |
Decorative metallic coatings for radio wave transmissive application products — Designation and characterization method |
ISO/DIS 5154 |
5154 |
1 |
2022 |
SDG 9
|
| ISO |
ISO/TC 94/SC 15 |
Respiratory protective devices — Methods of test and test equipment — Part 4: Determination of gas filter capacity and migration, desorption and carbon monoxide dynamic testing |
ISO 16900-4:2011 |
16900 |
1 |
2011 |
SDG 3
|
| ASTM |
D22.04 |
Practice for Collection of Airborne Particulate Lead During Abatement and Construction Activities |
E1553 |
E1553 |
|
1993 |
SDG 11
|
| ISO |
ISO/TC 34/SC 3 |
Shelled sweet kernels of apricots — Specification |
ISO 6479:1984 |
6479 |
1 |
1984 |
SDG 2
|
| ISO |
ISO/TC 46/SC 4 |
Information and documentation — Commands for interactive text searching |
ISO 8777:1993 |
8777 |
1 |
1993 |
SDG 4
|
| ISO |
ISO/TC 45/SC 2 |
Rubber — Identification of antidegradants by gas chromatography/mass spectrometry |
ISO 10638:2017 |
10638 |
2 |
2017 |
SDG 9
|
| ASTM |
C13.02 |
Specification for Steel Fiber Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe |
C1765 |
C1765 |
|
2019 |
SDG 6, 11, 12
|
| ISO |
ISO/TC 135/SC 5 |
Non-destructive testing — Image quality of radiographs — Part 5: Determination of the image unsharpness and basic spatial resolution value using duplex wire-type image quality indicators |
ISO 19232-5:2018 |
19232 |
3 |
2018 |
SDG 8
|
| IEC |
TC 48/SC 48B |
Connectors for electronic equipment - Tests and measurements - Part 9-2: Endurance tests - Test 9b: Electrical load and temperature |
IEC 60512-9-2:2011 |
60512-9-2:2011 |
1 |
2011 |
SDG 3, 4, 6, 7, 9, 11, 12, 13, 16, 17
|
| IEC |
TC 121/SC 121A |
Low-voltage switchgear and controlgear - Part 7-4: Ancillary equipment - PCB terminal blocks for copper conductors |
IEC 60947-7-4:2019 |
60947-7-4:2019 |
2 |
2019 |
SDG 1, 2, 3, 4, 6, 8, 9, 11, 12, 13, 14, 17
|
| ISO |
ISO/TC 43/SC 1 |
Acoustics — Acoustic quality of open office spaces |
ISO 22955:2021 |
22955 |
1 |
2021 |
SDG 3
|
| ISO |
ISO/TC 8/SC 6 |
Ships and marine technology — Guidelines for the assessment of speed and power performance by analysis of speed trial data |
ISO 15016:2015 |
15016 |
2 |
2015 |
SDG 9
|
| ISO |
ISO/TC 22/SC 34 |
Passenger cars — Engine cooling systems — Dimensions of pressure caps and their ramp seats on filler necks |
ISO 9817:1991 |
9817 |
1 |
1991 |
SDG 9
|
| ISO |
ISO/TC 20/SC 4 |
Aerospace — Rivets, solid, 100 degrees normal countersunk head, in metallic material, with or without surface treatment — Dimensions |
ISO 12281:1999 |
12281 |
1 |
1999 |
SDG 9
|
| ISO |
ISO/TC 45/SC 1 |
Rubber hoses and hose assemblies for dispensing liquefied petroleum gases (LPGs) — Specification |
ISO 11759:1999 |
11759 |
1 |
1999 |
SDG 7
|
